HSGQ-SFP28-DAC:
· Support for multi-gigabit data rates up to 25Gbps
· Hot-pluggable
· I/O Connector designed for high speed differential signal applications
· Improved Pluggable FormFactor(IPF) compliant for enhanced EMI/EMC performance
| Quantity: | |
|---|---|
HSGQ’s 25g SFP28 passive cable uses shielded high-speed differential cable, whichIt conforms to 25g Ethernet ieee802.3by standard and sff-8402 sfp28 standard, supports 25g transmission rate, and is also downward compatible with low rate applications. Sfp28 passive cable is the preferred solution for 25g rate short distance application, which is widely used in data transmission between data center and cabinet or between adjacent cabinets. Its biggest characteristics are low cost, ultra-low power consumption (less than 0.1W) and high reliability.
Features
● Support for multi-gigabit data rates up to 25Gbps
● Hot-pluggable
● I/O Connector designed for high speed differential signal applications
● Improved Pluggable FormFactor(IPF) compliant for enhanced EMI/EMC performance
● Compatible to SFF-8402 and SFF-8432
● Compatible to SFP28 MSA
● Compatible to IEEE 802.3ba
● Power Supply :+3.3V
● Low power consumption: 0.02 W (typ.)
● Temperature Range: 0~ 70 °C
● Comply with RoHS 6.0
Applications
● 25g Ethernet
● High capacity I/O in Storage Area Networks, Network Attached Storage, and Storage Servers
● Switched fabric I/O such as ultra high bandwidth switches and routers
● Data center cabling infrastructure
● High density connections between networking equipment
Recommended Operating Conditions
High Speed Characteristics
Notes:
1.Reflection Coefficient given by equation SDD11(dB) < 16.5 - 2 × SQRT(f ), with f in GHz
2.Reflection Coefficient given by equation SDD11(dB) < 10.66 - 14 × log10(f/5.5), with f in GHz
3.Reflection Coefficient given by equation SCD11(dB) < 22 - (20/25.78)*f, with f in GHz
4.Reflection Coefficient given by equation SCD11(dB) < 15 - (6/25.78)*f, with f in GHz
5.Reflection Coefficient given by equation SCD21(dB) < 27 - (29/22)*f, with f in GHz
Pin Descriptions
1.Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor
2.Passive cable assemblies do not support LOS and TX_DIS
Mechanical Dimensions
Ordering information
Note: You can be customized diameter and distance.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by company before they become applicable to any particular order or contract. In accordance with company policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of company or others. Further details are available from any company sales representative.
HSGQ’s 25g SFP28 passive cable uses shielded high-speed differential cable, whichIt conforms to 25g Ethernet ieee802.3by standard and sff-8402 sfp28 standard, supports 25g transmission rate, and is also downward compatible with low rate applications. Sfp28 passive cable is the preferred solution for 25g rate short distance application, which is widely used in data transmission between data center and cabinet or between adjacent cabinets. Its biggest characteristics are low cost, ultra-low power consumption (less than 0.1W) and high reliability.
Features
● Support for multi-gigabit data rates up to 25Gbps
● Hot-pluggable
● I/O Connector designed for high speed differential signal applications
● Improved Pluggable FormFactor(IPF) compliant for enhanced EMI/EMC performance
● Compatible to SFF-8402 and SFF-8432
● Compatible to SFP28 MSA
● Compatible to IEEE 802.3ba
● Power Supply :+3.3V
● Low power consumption: 0.02 W (typ.)
● Temperature Range: 0~ 70 °C
● Comply with RoHS 6.0
Applications
● 25g Ethernet
● High capacity I/O in Storage Area Networks, Network Attached Storage, and Storage Servers
● Switched fabric I/O such as ultra high bandwidth switches and routers
● Data center cabling infrastructure
● High density connections between networking equipment
Recommended Operating Conditions
High Speed Characteristics
Notes:
1.Reflection Coefficient given by equation SDD11(dB) < 16.5 - 2 × SQRT(f ), with f in GHz
2.Reflection Coefficient given by equation SDD11(dB) < 10.66 - 14 × log10(f/5.5), with f in GHz
3.Reflection Coefficient given by equation SCD11(dB) < 22 - (20/25.78)*f, with f in GHz
4.Reflection Coefficient given by equation SCD11(dB) < 15 - (6/25.78)*f, with f in GHz
5.Reflection Coefficient given by equation SCD21(dB) < 27 - (29/22)*f, with f in GHz
Pin Descriptions
1.Signals not supported in SFP+ Copper pulled-down to VeeT with 30K ohms resistor
2.Passive cable assemblies do not support LOS and TX_DIS
Mechanical Dimensions
Ordering information
Note: You can be customized diameter and distance.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by company before they become applicable to any particular order or contract. In accordance with company policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of company or others. Further details are available from any company sales representative.
